 |
B3307 |
69-71 |
BAFFLE - metering block vent, center carburetor |
5.65 |
|
 |
B3800 |
69-71 |
BASE - secondary diaphragm, Holley end carburetor |
89.95 |
|
| |
B5027U |
69-71 |
BOWL - center carburetor, Holley #4374, 4375, 4391, 4392, ALL w/small rubber vent cap & no RH vapor return line, reconditioned |
149.95 |
|
| |
M1530C |
69-71 |
BOWL - center carburetor, Holley #4144, 4669, 4670, 4791, 4792, w/special vent & vapor return tube, RECONDITIONED ORIGINAL |
174.95 |
|
 |
M5001 |
69-71 |
BOWL - end carburetor, Holley #4175, 4365, 4382, 4383, 4393, 4394, 4671, 4672, 4789, 4790 |
174.95 |
|
| |
M5001U |
1969-71 |
BOWL - end carburetor, Holley #4175, 4365, 4382, 4383, 4393, 4394, 4671, 4672, 4789, 4790, RECONDITIONED ORIGINAL |
174.95 |
|
 |
B3311 |
69-71 |
BRACKET - float, in fuel bowl |
1.85 |
|
| |
B3737 |
69-71 |
BUSHING KIT - tri power linkage, 1 large & 2 small bushings, special bolt & locking nut/used at center pivot |
16.95 |
|
 |
B3531 |
69-71 |
BUSHING SET - throttle shaft, to repair worn out throttle shaft holes in base plate, may require reaming of base, brass (2 pc) |
6.00 |
|
 |
M3890 |
69-71 |
CAGE/LEVER - fast idle plastic cam |
24.95 |
|
 |
B3560 |
69-71 |
CAM - accelerator pump on throttle shaft arm, Holley center carburetor, white plastic |
4.95 |
|
 |
M3889 |
69-71 |
CAM/ACTUATOR - choke, plastic, RH side of carburetor on stud |
29.95 |
|
 |
B3647 |
69-71 |
CAM KIT - accelerator pump, on throttle shaft arm, allows custom tailoring of accelerator pump response (8 different profiles
& colors) |
30.95 |
|
| |
N1550 |
69-71 |
CAP/RETAINER - vapor return line plunger |
10.95 |
|
 |
B1572 |
69-71 |
CARBURETOR KIT - Holley, six pack end |
42.95 |
|
|
B1572 |
69-71 |
CARBURETOR KIT - Holley, six pack center |
42.95 |
|
 |
M3899 |
69-71 |
CHOKE KIT - center carburetor / complete |
169.95 |
|
| |
B5012K |
69-71 |
CHOKE KIT/UPPER - all SIX PACK center carburetors, choke cross shaft, butterfly & screw set, 4pc, RH side of carburetor |
32.95 |
|
 |
M3887 |
69-71 |
CHOKE PULL-OFF - center carburetor |
32.95 |
|
 |
M3887C |
69-71 |
CHOKE PULL-OFF - center carburetor, curved pipe as original |
54.95 |
|
 |
B3608 |
69-71 |
COVER - accelerator pump (30 cc), w/beveled screw holes for tapered clutch head screw set #B3772 |
34.95 |
|
 |
B3570 |
69-71 |
COVER - accelerator pump (30 cc), for use w/Phillips non-tapered screw set #B3767 |
15.95 |
|
 |
M1542 |
69-71 |
COVER - hot air idle compensator |
19.95 |
|
 |
B3899 |
69-71 |
COVER - secondary diaphragm, all tri-power end carburetors, Holley |
CALL |
|
 |
B3898 |
69-71 |
DIAPHRAGM - carburetor, secondary, all six pack, Holley end carburetor |
48.95 |
|
 |
B3972 |
69-71 |
DIAPHRAGM KIT - secondary, includes diaphragm, base, cover, spring, link, gasket set, retainer & all required screws
(1 kit req. per end carburetor) |
199.95 |
|
 |
A3843 |
69-71 |
FILTER - fuel, bronze, behind fuel inlet nut (1 req. per carb.) |
7.95 |
|
 |
B3136 |
69-71 |
FILTER KIT - 3 each, fuel filters, inlet nut gaskets, fuel filter gaskets and fuel filter springs |
23.95 |
|
| |
B3170 |
69-71 |
FITTING - accelerator pump adjusting on lever |
3.25 |
|
 |
B3779 |
69-71 |
FITTING - vacuum, connects 2 tri-power end carbs to center, T shape, plastic |
2.95 |
|
 |
B5012 |
69-71 |
FLAP/PLATE - choke |
13.95 |
|
 |
B5036 |
69-71 |
FLOAT - carburetor, all six pack, end carburetors |
20.85 |
|
 |
B5037 |
69-71 |
FLOAT - carburetor, all six pack center carburetors |
16.95 |
|
 |
B5030 |
69-71 |
FLOAT KIT - Holley six pack carburetor set, 1 center and 2 end carburetor floats |
54.95 |
|
 |
B3892 |
69-71 |
FUEL INLET FITTING - Holley six pack carburetor, 5/16 inlet size, BLACK FINISH |
9.95 |
|
| |
B3892G |
69-71 |
FUEL INLET FITTING - Holley six pack carburetor, 5/16 inlet size, YELLOW CAD & DICHROMATE FINISH |
9.95 |
|
 |
M3811 |
69-71 |
FUEL INLET & FILTER KIT - for all 3 carburetors / 15 pc. 3 ea. fittings, filter, filter spring and large & small gaskets |
35.95 |
|
| |
RPX6802 |
70-71 |
FUEL LINE KIT - pump to carburetors, 340 Six Pack, 8pc |
54.95 |
|
 |
M3809 |
69-70 |
FUEL LINE KIT - pump to carburetors, 440 Six Pack, 8pc |
54.95 |
|
| |
RPC6802 |
70-71 |
FUEL LINE KIT - lower/340 six pack, 2 pc |
24.95 |
|
| |
RPC6803 |
69-70 |
FUEL LINE KIT - lower/440 six pack, 2 pc |
31.95 |
|
| |
RPC6801 |
69-71 |
FUEL LINE KIT - upper all 340/440 systems, standard tubing, 6pc |
42.95 |
|
| |
SPC6801 |
69-71 |
FUEL LINE KIT - upper all 340/440 systems, stainless steel tubing, 6pc |
65.95 |
|
 |
B3175 |
69-71 |
GASKET - fuel inlet, large |
1.65 |
|
 |
B3177 |
69-71 |
GASKET - fuel filter, small |
1.10 |
|
 |
B4076 |
69-71 |
GASKET - main body to base plate, center carburetors |
3.65 |
|
| |
B4028 |
69-71 |
GASKET - main body to base plate, Holley end carburetors |
4.50 |
|
 |
B3543 |
69-71 |
GASKET - metering plate (die cast) to metering plate, steel |
2.65 |
|
 |
B4070 |
69-71 |
GASKET - power valve |
1.35 |
|
| |
M1503 |
70-71 |
GASKET/SEAL - cover/cap hot air idle compensator |
1.85 |
|
| |
M1503K5 |
ALL |
GASKET/SEAL - 5pc set, hot air idle compensator cover |
11.95 |
|
| |
M1503K2 |
70-71 |
GASKET/SEAL - 10pc, cover/cap hot air idle compensator |
14.95 |
|
 |
M0110 |
69-71 |
GASKET SET - six pack carburetors to air cleaner / 3pc
|
9.75 |
|
 |
B3541 |
69-71 |
GASKET SET - bowl to metering block (2 pc) |
3.50 |
|
 |
B0606 |
69-71 |
GASKET SET - carburetors to intake, six pack (3 pc) |
10.95 |
|
| |
Z4076 |
69-71 |
GASKET SET - 3x2 carburetor bodies to base plate, 1 center & 2 end carburetors (3 pc.) |
9.95 |
|
 |
B3561 |
69-71 |
GASKET SET - fuel bowl screws (8 pc) |
4.35 |
|
 |
B3862 |
69-71 |
GASKET SET - idle air screws (2 pc) |
1.75 |
|
 |
B3515 |
69-71 |
GASKET SET - metering block to main body (2 pc) |
2.95 |
|
 |
B3162 |
69-71 |
GASKET SET - needle, seat nut & screw (4 pc / 2 sets) |
8.95 |
|
 |
B4074 |
69-71 |
GASKET SET - nozzle squirter (2 pc) |
1.65 |
|
 |
B5038 |
69-71 |
GASKET SET - secondary diaphragm housing base to end carburetor body (2 pc) |
1.95 |
|
 |
B4072 |
69-71 |
GASKET SET - sight plugs (2 pc) |
1.65 |
|
 |
B3544 |
69-71 |
GASKET SET - steel metering plate to main body (2 pc) |
3.25 |
|
 |
B5015 |
69-71 |
GUIDE - choke rod, six pack center carburetor, white plastic |
2.05 |
|
 |
B3650 |
69-71 |
HOSE KIT - tri-power carbs, end carburetors to center, & choke pull-off, w/\"T\" fitting |
10.65 |
|
 |
M5002 |
70-71 |
HOT AIR IDLE COMPENSATOR - some 1970 & 1971 center carbs, mount on back of main body under rectangular cover |
29.95 |
|
| |
M1502K |
69-71 |
HOT AIR IDLE COMPENSATOR KIT - compensator, cover & screws/4pc |
CALL |
|
 |
B3654 |
69-71 |
INSTALLATION KIT - needle & seats, 10pc |
16.95 |
|
 |
B3583 |
69-71 |
INSULATOR KIT - 3 SIX PACK CARBS to intake manifold..includes 3 1/4" phenolic insulators, 12 studs with lock washers & nuts and 6 installation gaskets |
159.95 |
|
 |
B3648 |
70 |
JET SET - Holley #4391 (pr) |
7.95 |
|
 |
B3649 |
69-71 |
JET SET - Holley #4144, 4670, 4791 (pr) |
7.95 |
|
 |
B3634 |
69-71 |
JET SET - Holley #4374, 4375, 4392, 4669 (pr) |
7.95 |
|
| |
C3621 |
70-71 |
JET SET - Holley #4792 (pr) |
7.95 |
|
 |
B3894 |
69-71 |
LEVER - accelerator pump, on stud |
5.95 |
|
 |
B4075 |
69-71 |
LEVER - accelerator pump cover |
2.95 |
|
| |
M3850 |
69-71 |
LEVER - choke control, screws to throttle shaft, contacts plastic cam, RH |
37.95 |
|
| |
M1516 |
69-71 |
LEVER/ARM - bowl vent, Holley #4374, 4375, 4391, 4392, uses rubber stopper/not for carbs w/vapor return system & tube type vent on RH side |
24.95 |
|
| |
M1515 |
69-71 |
LEVER/ARM - bowl vent, Holley #4144, 4669, 4670, 4791, 4792, w/vapor return tube |
CALL |
|
 |
M3891 |
69-71 |
LINK - fast idle cam cage to choke pull-off |
12.95 |
|
 |
B5020 |
69-71 |
LINK - secondary diaphragm, on throttle shaft, RH, each |
21.95 |
|
 |
B5085 |
69-71 |
LINK & SCREW SET - link on end of throttle shaft w/screw, all end carburetors, 2 of each, 4pc |
39.95 |
|
| |
M1543 |
M1544 |
METERING BLOCK - Holley #4144, 4374, 4375, 4669, 4670 |
CALL |
|
| |
M1544 |
69-71 |
METERING BLOCK - Holley #4391, 4392 |
CALL |
|
| |
M1545 |
70-71 |
METERING BLOCK - Holley #4791, 4792 |
CALL |
|
| |
M1536 |
69-71 |
METERING PLATE - fuel, die cast, Holley #4175, 4382, 4671 front carburetor, w/440 (34R-6153-34) |
CALL |
|
| |
B0608 |
70 |
METERING PLATE - fuel, die cast, Holley #4393, 4394 end carburetor, w/440 |
39.95 |
|
 |
M1527 |
69-71 |
METERING PLATE - fuel, die cast, Holley #4365, 4383, 4672, w/440, rear carburetor (34R-6153-35) |
62.95 |
|
 |
B3391 |
69-71 |
METERING PLATE - fuel, thin steel, all w/die cast metering plate, rear |
6.25 |
|
 |
B1543 |
69-71 |
NEEDLE & SEAT SET - (ea) |
10.95 |
|
| |
B3318 |
69-71 |
NEEDLE VALVE - pump discharge nozzle |
2.25 |
|
| |
C1511 |
69-71 |
NOZZLE - pump discharge |
11.95 |
|
| |
B4025 |
69-71 |
NUT - needle & seat height locking |
1.85 |
|
| |
B3301 |
69-71 |
PIN - float to bracket |
1.65 |
|
| |
M1529 |
69-71 |
PIN SET - base plate, end carburetor (pr) |
1.00 |
|
| |
M1525 |
69-71 |
PLATE SET - throttle shaft, Holley six pack end carburetor, aluminum w/.070 bleed hole (2 pc) |
52.95 |
|
| |
M1526 |
69-71 |
PLATE SET - throttle shaft, Holley six pack center carburetor (2 pc) |
49.95 |
|
 |
B3551 |
69-71 |
PLUG - metering block wells, 1/4", all Holley carburetors |
1.45 |
|
 |
B3551K |
69-71 |
PLUG SET - metering block wells, 1/4", all Holley carburetors, 10PC |
7.45 |
|
 |
B3990 |
69-71 |
PLUG/SCREW - fuel bowl, to check fuel level |
2.85 |
|
 |
N1551 |
69-71 |
PLUNGER & SEAL - vapor return bowl/reconditioned |
15.95 |
|
 |
B4079 |
69-71 |
POWER VALVE - Holley six pack center carburetor, metering block |
7.95 |
|
 |
B3507 |
69-71 |
PUMP - accelerator (30 cc) |
8.95 |
|
| |
M3800 |
67-69 |
REPAIR - end carburetor idle air passages/boring, sleeving & machining |
CALL |
|
| |
M3800K |
69-71 |
REPAIR W/SCREW SET - end carburetor idle air passages/boring, sleeving & machining, & 2 correct screws |
CALL |
|
| |
B3646 |
69-71 |
RETAINER - accelerator pump arm to cover |
1.25 |
|
| |
M1535 |
69-71 |
RETAINER - throttle shaft lever |
10.95 |
|
 |
B3896 |
69-71 |
RETAINER - bowl vent lever |
CALL |
|
| |
B4087 |
69-71 |
RETAINER - floats (pr) |
1.00 |
|
| |
B3174 |
69-71 |
RETAINER/E CLIP - accelerator pump lever, choke cam & cage shaft |
1.55 |
|
| |
B3356 |
69-71 |
RETAINER/E CLIP - secondary diaphragm rod to link |
1.25 |
|
| |
B5021 |
69-71 |
ROD - choke shaft to choke plastic cam cage/lever, Holley #4374, 4375, 4391, 4392, 4144, 4669, 4670, 4791, 4792 |
14.95 |
|
| |
B3172 |
69-71 |
SCREW - accelerator pump adjusting on lever |
4.25 |
|
| |
B3354 |
69-71 |
SCREW - air/fuel mixture, metering block |
3.75 |
|
| |
B3317 |
69-71 |
SCREW - accelerator pump cam retainer, on accelerator lever |
1.75 |
|
| |
K2228 |
69-71 |
SCREW - accelerator linkage lever clip/used w/M1535 |
CALL |
|
| |
B3325 |
69-71 |
SCREW - bowl vent lever retainer |
1.25 |
|
| |
B3769 |
69-71 |
SCREW - fast idle & retainer on accelerator lever |
1.65 |
|
| |
B3883S |
69-71 |
SCREW - fuel bowl, 2.0" length, original/slotted, ea |
3.15 |
|
| |
B3883L |
69-71 |
SCREW - fuel bowl, 2.5” length, original/slotted, ea |
3.15 |
|
| |
M1513 |
69-71 |
SCREW - idle air, in end carburetor base (2 req., ea) |
14.25 |
|
 |
B0615 |
69-71 |
SCREW - lever to throttle shaft, RH side (ea) |
1.65 |
|
| |
B3392 |
69-71 |
SCREW - needle & seat height adjusting |
1.95 |
|
| |
B3309 |
69-71 |
SCREW - pump discharge nozzle |
1.95 |
|
| |
N1519 |
69-71 |
SCREW DRIVER - clutch head design, used on end carburetor metering plate & some accelerator pump covers |
19.95 |
|
| |
B3767 |
69-71 |
SCREW SET - accelerator pump (30 cc) cover, Phillips head, 3/8” long, used on B3570 cover (4 pc) |
3.65 |
|
 |
B3572 |
69-71 |
SCREW SET - accelerator pump (30 cc) cover, tapered clutch head, 3/8” long (4 pc), used on cover B3508 |
6.75 |
|
| |
M1540 |
69-71 |
SCREW SET - cover/cap, hot air idle compensator |
1.50 |
|
| |
B3872 |
69-71 |
SCREW SET - choke flap (2 pc). |
2.25 |
|
| |
B3957 |
69-71 |
SCREW SET - choke pull-off retaining (2 pc) |
3.25 |
|
| |
B3305 |
69-71 |
SCREW SET - float bracket retaining (2 pc) |
2.15 |
|
| |
B3535 |
69-71 |
SCREW SET - fuel bowl, current design, 2.0”, Holley end carburetor, current design/hex end (4 pc) |
9.00 |
|
| |
B3883 |
69-71 |
SCREW SET - fuel bowl, Holley center carburetor, 2.5", current design/hex end (4 pc) |
7.95 |
|
 |
B4026 |
69-71 |
SCREW SET - metering plate to main body, Holley end carburetor, clutch head (6 pc) |
7.25 |
|
| |
M1531 |
69-71 |
SCREW SET - plunger cap/retainer (pr) |
3.25 |
|
| |
M1531 |
69-71 |
SCREW SET - hot air idle compensator cover |
3.25 |
|
| |
B3550 |
69-71 |
SCREW SET - throttle body to carburetor main body (5 pc) |
4.65 |
|
| |
B3530 |
69-71 |
SCREW SET - throttle plates to shaft, center carburetors (8 pc) |
4.50 |
|
| |
M3892 |
69-71 |
SCREW SET - throttle plates to shaft, end carburetors (4 pc) |
4.95 |
|
| |
B3502 |
69-71 |
SCREW SET - vacuum secondary diaphragm base to Holley end carburetor body (4 pc) |
5.25 |
|
| |
B3500 |
69-71 |
SCREW SET - vacuum secondary diaphragm cover to base, Holley end carburetor (6 pc) |
4.45 |
|
| |
N1551S |
ALL |
SEAL - bowl vent plunger/used to service N1551 |
2.45 |
|
 |
B3480 |
69-71 |
SEAL - bowl vent, rubber, snaps into bowl vent lever |
2.10 |
|
 |
B3884 |
69-71 |
SHAFT - choke flap/plate |
21.25 |
|
| |
B3321 |
69-71 |
SHAFT ASSEMBLY - throttle, w/lever, Holley end carburetor, USED ORIGINAL |
79.95 |
|
| |
B3171 |
69-71 |
SPRING - accelerator pump adjusting on lever |
2.75 |
|
| |
B3355 |
69-71 |
SPRING - accelerator pump diaphragm |
1.65 |
|
| |
N1533 |
69-71 |
SPRING - bowl vent lever, Holley center carburetor |
4.75 |
|
| |
B3953 |
69-71 |
SPRING - fast idle screw |
1.95 |
|
| |
B3617 |
69-71 |
SPRING - float |
2.45 |
|
 |
B3176 |
69-71 |
SPRING - fuel filter, in front bowl |
2.95 |
|
| |
N1552 |
69-71 |
SPRING - vapor plunger |
3.95 |
|
| |
B3629 |
69-71 |
SPRING - secondary diaphragm, Holley end carburetor |
4.50 |
|
 |
B5006 |
69-71 |
SPRING KIT - secondary diaphragm, 7 springs for adjusting accelerator response |
32.95 |
|
| |
A3955 |
69-71 |
STAND KIT - carburetor, elevates 2\", facilitates servicing of the lower end of the carburetor (4 pc) |
12.95 |
|
| |
B3768 |
69-71 |
STUD - accelerator pump lever, on base plate, LH front |
2.50 |
|
| |
B3538 |
69-71 |
STUD - choke cam & cage, presses into main body, RH |
19.95 |
|
| |
N1650 |
69-71 |
TOOL - main jet removal |
26.95 |
|
| |
B3533 |
69-71 |
TUBE - air horn bowl vent, front, short, straight cut |
2.65 |
|
| |
B3529 |
69-71 |
TUBE - air horn bowl vent, front, long, angle cut |
2.85 |
|
| |
B3534 |
69-71 |
TUBE - air horn bowl vent, front, long, straight cut |
2.65 |
|
| |
M3550 |
69-71 |
TUBE - vacuum, SIX PACK center carburetor metering block, RH with curve |
7.95 |
|
| |
B3528 |
69-71 |
TUBE - bowl vent air horn, front, short (angle cut) |
2.85 |
|
| |
B3511 |
69-71 |
TUBE - vacuum hose on RH side, all six pack carbs/base six pack centers |
4.65 |
|
| |
B3512 |
69-71 |
TUBE - base, outer, RH, large |
5.95 |
|
Holley 2-Barrel Six-Pack Carburetors - Mopar
